P83CE558EBBSLASHYYY datasheet(21/72 Pages) PHILIPS

21 / 72 page

Philips Semiconductors

Preliminary specification

P83CE558/P80CE558/P89CE558

Single-chip 8-bit microcontroller

1996 Aug 06

6.6.2

Configuration and Operation

Every A/D conversion is an autoscan conversion. The two user

selectable general operation modes are continuous scan and

one-time scan mode.

The desired analog input port channel/s for conversion is/are

selected by programming A/D input port scan-select bits in SFR

ADPSS. An analog input channel is included in the autoscan loop if

the corresponding bit in ADPSS is 1, a channel is skipped if the

corresponding bit in ADPSS is 0.

An autoscan is always started according to the lowest bit position of

ADPSS that contains a 1.

An autoscan conversion is started by setting the flag ADSST in

input pin ADEXS, if enabled. Either no edge (external start totally

disabled), a rising edge or/and a falling edge of ADEXS is selectable

for external conversion start by the bits ADSRE and ADSFE in

After completion of an A/D conversion the 10-bit result is stored in

the corresponding 10-bit buffer register. Then the next analog input

is selected according to the next higher set bit position in ADPSS,

converted and stored, and so on. When the result of the last

conversion of this autoscan loop is stored, flag ADCON.4/ADINT,

the ADC interrupt flag, is set. It is not cleared by interrupt hardware

– it must be cleared by software.

In continuous scan mode (ADCON.2/ADCSA=1) the ADC start and

status flag ADCON.3/ADSST retains the set state and the autoscan

loop restarts from the beginning. In one-time scan mode (ADCSA=0)

conversions stop after the last selected analog input was converted,

ADINT is set and ADSST is cleared automatically.

ADSST cannot be set (neither externally nor by software) as long as

ADINT=1, i.e. as long as ADINT is set, a new conversion start – by

setting flag ADSST – is inhibited; actually it is only delayed until

ADINT is cleared.

(If a ‘1’ is written to ADSST while ADINT=1, this new value is

internally latched and preserved, not setting ADSST until

ADCON.4/ADINT=0. In this state, a read of SFR ADCON will display

ADCON.3/ADSST=0, because always the effective ADC status is

read.)

Note that under software control the analog inputs can also be

converted in arbitrary order, when one-time scan mode is selected

and in SFR ADPSS only one bit is set at a time. In this case ADINT

is set and ADSST is cleared after every conversion.

6.6.3

Resolution and Characteristics

The ADC system has its own analog supply pins AVDD and AVSS. It

is referenced by two special reference voltage input pins sourcing

the resistance ladder of the DAC: AVref+ and AVref–. The voltage

between AVREF+ and AVREF– defines the full-scale range. Due to

the 10-bit resolution the full scale range is divided into 1024 unit

steps. The unit step voltage is 1 LSB, which is typically 5 mV

(AVref+ = 5.12 V, AVref– = 0 V = AVSS).

The DAC’s resistance ladder has 1023 equally spaced taps,

separated by a unit resistance ’R’. The first tap is located 0.5 x R

above AVref–, the last tap is located 1.5 x R below AVref+. This

results in a total ladder resistance of 1024 x R. This structure

ensures that the DAC is monotonic and results in a symmetrical

quantization error. For input voltages between AVref– and

(AVref– + 1/2 LSB) the 10-bit conversion result code will be

00 0000 0000 B = 000H = 0D. For input voltages between

(AVref+ – 3/2 LSB) and AVref+ the 10-bit conversion result code will

be 11 1111 1111 B = 3FFH = 1023D.

The result code corresponding to an analog input voltage (AVin) can

be calculated from the formula:

ResultCode

+ 1024

IN *

ref

) *

ref

The analog input voltage should be stable when it is sampled for

conversion. At any times the input voltage slew rate must be less

than 10 V/ms (5 V conversion range) in order to prevent an

undefined result.

This maximum input voltage slew rate can be ensured by an RC low

pass filter with R = 2k2 and C = 100 nF. The capacitor between

analog input pin and analog ground pin shall be placed close to the

pins in order to have maximum effect in minimizing input noise

coupling.

6.7

Timer/Counters

The P8xCE558 contains three 16-bit timer/event counters: Timer 0,

Timer 1 and Timer T2 and one 8-bit timer, T3. Timer 0 and Timer 1

may be programmed to carry out the following functions:

• Measure time intervals and pulse durations

• Count events

• Generate interrupt requests

6.7.1

Timer 0 and Timer 1

Timers 0 and 1 each have a control bit in SFR TMOD that selects

the timer or counter function of the corresponding timer.

In the timer function, the register is incremented every machine

cycle. Thus, one can think of it as counting machine cycles. Since a

machine cycle consists of 12 oscillator periods, the count rate is

1/12 of the oscillator frequency.

In the counter function, the register is incremented in response to a

1-to-0 transition at the corresponding external input pin, T0 or T1. In

this function, the external input is sampled during S5P2 of every

machine cycle. When the samples show a HIGH in one cycle and a

LOW in the next cycle, the counter is incremented. Thus, it takes

two machine cycles (24 oscillator periods) to recognize a 1-to-0

transition. There are no restrictions on the duty cycle of the external

input signal, but to insure that a given level is sampled at least once

before it changes, it should be held for at least one full machine

cycle.

Timer 0 and Timer 1 can be programmed independently to operate

in one of four modes:

• Mode 0:

8-bit timer or 8-bit counter each with divide-by-32 prescaler

• Mode 1:

16-bit time-interval or event counter

• Mode 2:

8-bit time-interval or event counter with automatic reload

upon overflow

• Mode 3:

–Timer 0: one 8-bit time-interval or event counter and

one 8-bit time-interval counter

–Timer 1: stopped

P83CE558EBB/YYY Scheda tecnica(PDF) 21 Page - NXP Semiconductors

P83CE558EBB/YYY Scheda tecnica(HTML) 21 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Scheda tecnica Scarica

Link URL