LAN9311 datasheet(53/459 Pages) SMSC

53 / 459 page

Two Port 10/100 Managed Ethernet Switch with 16-Bit Non-PCI CPU Interface

Datasheet

SMSC LAN9311/LAN9311i

Revision 1.6 (08-18-09)

DATASHEET

TX Status FIFO Overflow

Receive Watchdog Time-Out

Receiver Error

Transmitter Error

TX Data FIFO Underrun

TX Data FIFO Overrun

TX Data FIFO Available

TX Status FIFO Full

TX Status FIFO Level

RX Dropped Frame

RX Data FIFO Level

RX Status FIFO Full

RX Status FIFO Level

In order for a Host MAC interrupt event to trigger the external IRQ interrupt pin, the desired Host MAC

interrupt event must be enabled in the Interrupt Enable Register (INT_EN), and IRQ output must be

enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).

Refer to the Interrupt Status Register (INT_STS) on page 175 and Chapter 9, "Host MAC," on page 113

for additional information on bit definitions and Host MAC operation.

5.2.6

Power Management Interrupts

Multiple Power Management Event interrupt sources are provided by the LAN9311/LAN9311i. The top-

level PME_INT (bit 17) of the Interrupt Status Register (INT_STS) provides indication that a Power

Management interrupt event occurred in the Power Management Control Register (PMT_CTRL).

The Power Management Control Register (PMT_CTRL) provides enabling/disabling and status of all

Power Management conditions. These include energy-detect on the Port 1/2 PHYs, and Wake-On-LAN

(wake-up frame or magic packet) detection by the Host MAC.

In order for a Power Management interrupt event to trigger the external IRQ interrupt pin, the desired

Power Management interrupt event must be enabled in the Power Management Control Register

(PMT_CTRL) (bits 15, 14, and/or 9), bit 17 (PME_INT_EN) of the Interrupt Enable Register (INT_EN)

must be set, and IRQ output must be enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register

(IRQ_CFG).

For additional details on power management, refer to Section 4.3, "Power Management," on page 46.

5.2.7

General Purpose Timer Interrupt

A General Purpose Timer (GPT) interrupt is provided in the top-level Interrupt Status Register

(INT_STS) and Interrupt Enable Register (INT_EN) (bit 19). This interrupt is issued when the General

Purpose Timer Configuration Register (GPT_CFG) wraps past zero to FFFFh, and is cleared when bit

19 of the Interrupt Status Register (INT_STS) is written with 1.

In order for a General Purpose Timer interrupt event to trigger the external IRQ interrupt pin, the GPT

must be enabled via the bit 29 (TIMER_EN) in the General Purpose Timer Configuration Register

(GPT_CFG), bit 19 of the Interrupt Enable Register (INT_EN) must be set, and IRQ output must be

enabled via bit 8 (IRQ_EN) of the Interrupt Configuration Register (IRQ_CFG).

For additional details on the General Purpose Timer, refer to Section 12.1, "General Purpose Timer,"

on page 162.

LAN9311 Scheda tecnica(PDF) 53 Page - SMSC Corporation

LAN9311 Scheda tecnica(HTML) 53 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL