R7FA2L1AB2DFM datasheet(79/110 Pages) RENESAS

79 / 110 page

Table 2.56

Data flash characteristics (2) (2 of 2)

High-speed operating mode

Conditions: VCC = AVCC0 = 1.8 to 5.5 V

Parameter

Symbol

ICLK = 4 MHz

ICLK = 48 MHz

Unit

Min

Typ

Max

Min

Typ

Max

Data flash STOP recovery time

tDSTOP

250

—

250

—

Note:

Does not include the time until each operation of the flash memory is started after instructions are executed by software.

Note:

The lower-limit frequency of ICLK is 1 MHz during programming or erasing the flash memory. When using ICLK at below 4 MHz, the

frequency can be set to 1 MHz, 2 MHz, or 3 MHz. A non-integer frequency such as 1.5 MHz cannot be set.

Note:

The frequency accuracy of ICLK must be ± 1.0% during programming or erasing the flash memory. Confirm the frequency accuracy

of the clock source.

Table 2.57

Data flash characteristics (3)

Middle-speed operating mode

Conditions: VCC = AVCC0 = 1.6 to 5.5 V, Ta = -40 to +85°C

Parameter

Symbol

ICLK = 4 MHz

ICLK = 8 MHz*1

Unit

Min

Typ

Max

Min

Typ

Max

Programming time

1-byte

tDP1

—

404

—

356

µs

Erasure time

1-KB

tDE1K

—

8.8

280

—

7.3

248

Blank check time

1-byte

tDBC1

—

15.2

—

11.3

µs

1-KB

tDBC1K

—

1.84

—

1.06

Suspended time during erasing

tDSED

—

13.2

—

11.7

µs

Data flash STOP recovery time

tDSTOP

250

—

250

—

Note:

Does not include the time until each operation of the flash memory is started after instructions are executed by software.

Note:

The lower-limit frequency of ICLK is 1 MHz during programming or erasing the flash memory. When using ICLK at below 4 MHz, the

frequency can be set to 1 MHz, 2 MHz, or 3 MHz. A non-integer frequency such as 1.5 MHz cannot be set.

Note:

The frequency accuracy of ICLK must be ± 1.0% during programming or erasing the flash memory. Confirm the frequency accuracy

of the clock source.

Note 1. When 1.8 V ≤ VCC = AVCC0 ≤ 5.5 V

Table 2.58

Data flash characteristics (4)

Low-speed operating mode

Conditions: VCC = AVCC0 = 1.6 to 5.5 V, Ta = -40 to +85°C

Parameter

Symbol

ICLK = 1 MHz

ICLK = 2 MHz

Unit

Min

Typ

Max

Min

Typ

Max

Programming time

1-byte

tDP1

—

732

—

502

µs

Erasure time

1-KB

tDE1K

—

19.7

504

—

12.4

354

Blank check time

1-byte

tDBC1

—

46.5

—

23.3

µs

1-KB

tDBC1K

—

7.3

—

3.66

Suspended time during erasing

tDSED

—

22.3

—

16.2

µs

Data flash STOP recovery time

tDSTOP

250

—

250

—

Note:

Does not include the time until each operation of the flash memory is started after instructions are executed by software.

Note:

The lower-limit frequency of ICLK is 1 MHz during programming or erasing the flash memory. When using ICLK at below 2 MHz, the

frequency can be set to 1 MHz or 2 MHz. A non-integer frequency such as 1.5 MHz cannot be set.

Note:

The frequency accuracy of ICLK must be ± 1.0% during programming or erasing the flash memory. Confirm the frequency accuracy

of the clock source.

RA2L1 Datasheet

2. Electrical Characteristics

R01DS0385EJ0100 Rev.1.00

Aug 06, 2020

Page 79 of 110

R7FA2L1AB2DFM Scheda tecnica(PDF) 79 Page - Renesas Technology Corp

R7FA2L1AB2DFM Scheda tecnica(HTML) 79 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL