PIMXRT406LCAE4A datasheet(29/71 Pages) NXP

29 / 71 page

Electrical characteristics

i.MX RT1015 Crossover Processors Data Sheet for Consumer Products, Rev. 2, 03/2021

NXP Semiconductors

4.3.3

Output buffer impedance parameters

This section defines the I/O impedance parameters of the i.MX RT1015 processors for the following I/O

types:

•

Single Voltage General Purpose I/O (GPIO)

NOTE

GPIO I/O output driver impedance is measured with “long” transmission

line of impedance Ztl attached to I/O pad and incident wave launched into

transmission line. Rpu/Rpd and Ztl form a voltage divider that defines

specific voltage of incident wave relative to NVCC_XXXX. Output driver

impedance is calculated from this voltage divider (see Figure 6).

Table 21. General purpose I/O AC parameters 1.8 V mode

Parameter

Symbol

Test Condition

Min

Typ

Max

Unit

Output Pad Transition Times, rise/fall

(Max Drive, ipp_dse=111)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

2.72/2.79

1.51/1.54

Output Pad Transition Times, rise/fall

(High Drive, ipp_dse=101)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

3.20/3.36

1.96/2.07

Output Pad Transition Times, rise/fall

(Medium Drive, ipp_dse=100)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

3.64/3.88

2.27/2.53

Output Pad Transition Times, rise/fall

(Low Drive. ipp_dse=011)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

4.32/4.50

3.16/3.17

Input Transition Times1

1 Hysteresis mode is recommended for inputs with transition times greater than 25 ns.

trm

—

Table 22. General purpose I/O AC parameters 3.3 V mode

Parameter

Symbol

Test condition

Min

Typ

Max

Unit

Output Pad Transition Times, rise/fall

(Max Drive, ipp_dse=101)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

1.70/1.79

1.06/1.15

Output Pad Transition Times, rise/fall

(High Drive, ipp_dse=011)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

2.35/2.43

1.74/1.77

Output Pad Transition Times, rise/fall

(Medium Drive, ipp_dse=010)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

3.13/3.29

2.46/2.60

Output Pad Transition Times, rise/fall

(Low Drive. ipp_dse=001)

tr, tf

15 pF Cload, slow slew rate

15 pF Cload, fast slew rate

——

5.14/5.57

4.77/5.15

Input Transition Times1

1 Hysteresis mode is recommended for inputs with transition times greater than 25 ns.

trm

—

PIMXRT406LCAE4A Scheda tecnica(PDF) 29 Page - NXP Semiconductors

PIMXRT406LCAE4A Scheda tecnica(HTML) 29 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71

Scheda tecnica Scarica

Link URL