SP9841 datasheet(19/32 Pages) SIPEX

19 / 32 page

285

is requested, feedback within the op amp circuit

will force internal nodes to the rails, while the

output will remain saturated near this minimum

value. Non–saturated monotonic behavior returns

between 25mV and 100mV at the output, but full

open loop gain and linearity are not apparent until

the output voltage is nearly 100mV above the

negative supply. Applications which require good

linearity for codes near zero should drive the V

REFL

input at least 100mV above the ground pin, as this

insures that the output voltage will not go below

100mV for any legal input voltage. Two–quadrant

applications (programmable gain/attenuator) usually

biasV

REFL up at system pseudoground, well above this

saturation region, and therefore maintain linearity

even at high attenuations (i.e. at code 1).

The allowable, useful values of V

IN(X) and VREFL are

limited if a legal output value is to be expected for all

inputcodes.Atmaximumgain(DACcode255)V

OUT

isapproximatelyequalto2V

IN(X) – VREFL. By solving

thisequationtwice,oncewithV

OUT set to 0V, and then

again with Vout set to V

DD–1.5V, the chart of Figure

3a results. This chart can be used to find the maximal

IN(X) voltage excursions for any given voltage

driven into V

REFL. The upper line plots the maximum

voltage at V

IN(X) and the lower line plots the mini-

mum voltage at V

IN(X) at each value of VREFL drive.

Normal operation would be for V

IN(X) anywhere

between the two lines. For example, assume a 4.75V

supply voltage, and that the DAC code is set to 255. If

REFL is driven to 1.6V, VIN(X) below 0.8V would

require the output amplifier to swing below ground.

IN(X) above 2.425V would require output voltages

greater than V

DD – 1.5V, or 3.25V.

Figure 3b shows the limits on V

IN when the mini-

mumV

OUT is constrained to be greater than 100mV,

for extremely linear operation, even at DAC code

1. In this case, the lower line is 50mV above its

position in Figure 3a, except that below V

REFL =

100mV, the minimum input voltage stays at

100mV. It should be noted that V

IN(X) can always

be driven to or slightly beyond the supply rails

withoutharm.Undersuchcircumstances,theDAC

code can always be set to provide sufficient attenu-

ation to get an undistorted output.

Driving the Reference Inputs

The V

IN inputs exhibit a code–dependent input resis-

tance, as shown in the specifications. In general, these

inputs should be driven by an amplifier capable of

handling the specified load resistance and capaci-

tance. The reference inputs are useful for both ac and

dcinputsources.However,seriesresistanceintothese

pins will degrade the linearity of the DAC. A series

resistance of 50 Ohms can cause up to 0.5LSB of

additional integral linearity degradation for codes

near full scale, due to the code–dependent input

current dropping across this error resistance. AC–

coupled applications should use the largest capacitor

value (lowest series resistance) which is practical, or,

use an external buffer to drive the inputs.

The DAC switches function in a break–before–make

manner in order to minimize current spikes at the

reference inputs. As previously noted, the reference

inputs can withstand driving voltages slightly beyond

the power supply rails without harm. The gain of 2 at

the op amps limits the choice of V

IN/VREFL combina-

tions if clipping is to be avoided at the higher codes.

Output Considerations

Each DAC output amplifier can easily drive 1Kohm

loads in parallel with 15pF at its rated slew rate. The

uniqueBiCMOSamplifierdesignalsoensuresstabil-

ity into heavily capacitive loads — up to 47,000pF.

Undertheseconditions,theslewratewillbelimitedby

the instantaneous current available for charging the

capacitance—theslewratewillbeseverelydegraded,

and some damped ringing will occur. Especially

under heavy capacitive loading, a large, low imped-

ance local bypass capacitor will be required. A

0.047

µF ceramic in parallel with a low–ESR 2.2 to

µFtantalumarerecommendedforworst–caseloads.

The amplifier outputs can withstand momentary

shorts to V

DD or ground. Continuous short circuit

operation can result in thermally induced damage,

and should be avoided.

If the input reference voltage is reduced to 0.6V, then

both the amplifier and DAC are functional at room

temperatureatsupplyvoltagesaslowas2.5V.AtV

= 2.7V, power dissipation is 9.3mW typical, with the

serialclockat4MHz,or7.0mWtypicalwiththeserial

clock gated off.

Interfacing to the SP9841/SP9842

A simple serial interface, similar to that used in a

74HC594 shift–register with output latch, has been

implemented in these products. A serial clock is used

SP9841 Scheda tecnica(PDF) 19 Page - Sipex Corporation

SP9841 Scheda tecnica(HTML) 19 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

Scheda tecnica Scarica

Link URL