Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

MB91301 Scheda tecnica(PDF) 25 Page - Fuji Electric

Il numero della parte MB91301
Spiegazioni elettronici  32-Bit Proprietary Microcontroller
PDF  135 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  FUJI [Fuji Electric]
Homepage  http://www.fujielectric.co.jp/eng/fdt/scd
Logo FUJI - Fuji Electric

MB91301 Scheda tecnica(HTML) 25 Page - Fuji Electric

Back Button MB91301 Datasheet HTML 21Page - Fuji Electric MB91301 Datasheet HTML 22Page - Fuji Electric MB91301 Datasheet HTML 23Page - Fuji Electric MB91301 Datasheet HTML 24Page - Fuji Electric MB91301 Datasheet HTML 25Page - Fuji Electric MB91301 Datasheet HTML 26Page - Fuji Electric MB91301 Datasheet HTML 27Page - Fuji Electric MB91301 Datasheet HTML 28Page - Fuji Electric MB91301 Datasheet HTML 29Page - Fuji Electric Next Button
Zoom Inzoom in Zoom Outzoom out
 25 / 135 page
background image
MB91301 Series
25
• I-bus memory
Do not set a stack area or vector table in I-bus memory.
It may cause a hang during EIT processing (including RETI).
Recovery from the hang requires a reset.
Do not perform DMA transfer to I-bus memory.
• Low-power consumption modes
• To enter the standby mode, use the synchronous standby mode (set with the SYNCS bit as bit 8 in the
TBCR, or time-base counter control register) and be sure to use the following sequence:
(LDI
#value_of_standby, R0)
(LDI
#_STCR, R12)
STB
R0, @R12
; Write to standby control register (STCR)
LDUB
@R12, R0
; Read STCR for synchronous standby
LDUB
@R12, R0
; Read STCR again for dummy read
NOP
; NOP x 5 for timing adjustment
NOP
NOP
NOP
NOP
• If you use the monitor debugger, follow the precautions below:
Do not set a breakpoint within the above array of instructions.
Do not single-step the above array of instructions.
• Prefetch
When accessing a prefetch-enabled little endian area, use word access only (access in 32 bits).
Byte or halfword access results in wrong data read.
• MCLK and SYSCLK
MCLK causes a stop in SLEEP/STOP mode while SYSCLK causes a stop only in STOP mode. Use either
depending on each application.
• Pull-up control
When function pins listed in the AC specifications (such as external bus control pins) have pull-up control,
enabling the pull-up resistor for a pin causes the actual pin load conditions to change. As all AC specifications
for this device were measured under the condition of pull-up resistors disabled, the values are not guaranteed
of AC specifications when pull-up resistors are enabled.
Even if the pull-up resistor is set to enabled for a pin, if the HIZ bit in the standby control register (STCR) specifies
setting output pins to high impedance during stop mode (HIZ
= 1) , changing to stop mode (STOP = 1) causes
the pull-up resistor to be disabled.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Scheda tecnica Scarica

Go To PDF Page


Link URL



Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   Collegamento alla scheda tecnica    |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com