ADS1606IPAPR datasheet(17/38 Pages) TI

17 / 38 page

ADS1605

ADS1606

SBAS274H − MARCH 2003 − REVISED MAY 2007

www.ti.com

OVERVIEW

The ADS1605 and ADS1606 are high-performance delta-

sigma ADCs with a default oversampling ratio of 8. The

modulator uses an inherently stable 2-1-1 pipelined delta-

sigma modulator architecture incorporating proprietary

circuitry that allows for very linear high-speed operation.

The modulator samples the input signal at 40MSPS

(when fCLK = 40MHz). A low-ripple linear phase digital fil-

ter decimates the modulator output to provide data output

word rates of 5MSPS with a signal passband out to

2.45MHz. The 2X mode, enabled by a digital I/O pin,

doubles the data rate to 10MSPS by reducing the over-

sampling ratio to 4. See the 2X Mode section for more de-

tails.

Conceptually, the modulator and digital filter measure the

differential input signal, VIN = (AINP – AINN), against the

scaled differential reference, VREF = (VREFP – VREFN),

as shown in Figure 7. The voltage reference can either be

generated internally or supplied externally. An 16-bit paral-

lel data bus, designed for direct connection to DSPs, out-

puts the data. A separate power supply for the I/O allows

flexibility for interfacing to different logic families. Out-of-

range conditions are indicated with a dedicated digital out-

put pin. Analog power dissipation is controlled using an

external resistor. This allows reduced dissipation when

operating at slower speeds. When not in use, power con-

sumption can be dramatically reduced using the PD pin.

The ADS1606 incorporates an adjustable FIFO buffer for

the output data. The level of the FIFO is set by the

FIFO_LEV[2:0] pins. Other than the FIFO buffer, the

ADS1605 and ADS1606 are identical, and are referred to

together in this data sheet as the ADS1605/6.

ANALOG INPUTS (AINP, AINN)

The

ADS1605/6

measures

the

differential signal,

VIN = (AINP − AINN), against the differential reference,

VREF = (VREFP – VREFN). The reference is scaled inter-

nally so that the full-scale differential input voltage is

1.467VREF. That is, the most positive measurable differ-

ential input is 1.467VREF, which produces the most posi-

tive digital output code of 7FFFh. Likewise, the most neg-

ative measurable differential input is –1.467VREF, which

produces the most negative digital output code of 8000h.

The ADS1605/6 supports a very wide range of input sig-

nals. For VREF = 3V, the full-scale input voltages are

±4.4V. Having such a wide input range makes out-of-

range signals unlikely. However, should an out-of-range

signal occur, the digital output OTR will go high.

To achieve the highest analog performance, it is recom-

mended that the inputs be limited to

±1.165VREF

(−2dBFS). For VREF = 3V, the corresponding recom-

mended input range is

±3.78V.

The analog inputs must be driven with a differential signal

to achieve optimum performance. The recommended

common-mode

voltage

the

input

signal,

+ AINP ) AINN

, is 2.0V. For signals larger than

−2dBFS, the input common-mode voltage needs to be

raised in order to meet the absolute input voltage specifi-

cations. The Typical Characteristics show how perfor-

mance varies with input common-mode voltage.

In addition to the differential and common-mode input volt-

ages, the absolute input voltage is also important. This is

the voltage on either input (AINP or AINN) with respect to

AGND. The range for this voltage is:

* 0.1V t (AINN or AINP) t 4.6V

If either input is taken below –0.1V, ESD protection diodes

on the inputs will turn on. Exceeding 4.6V on either input

will result in degradation in the linearity performance. ESD

protection diodes will also turn on if the inputs are taken

above AVDD (+5V).

For signals below –2dBFS, the recommended absolute

input voltage is:

* 0.1V t (AINN or AINP) t 4.2V

Keeping the inputs within this range provides for optimum

performance.

Σ∆

Modulator

Digital

Filter

Parallel

Interface

1.467V

REF

1.467

REF

VREFN

IOVDD

VREFP

AINP

AINN

OTR

2XMODE

FIFO_LEV[2:0]

DOUT[15:0]

ADS1606 Only

FIFO

Figure 7. Conceptual Block Diagram

ADS1606IPAPR Scheda tecnica(PDF) 17 Page - Texas Instruments

ADS1606IPAPR Scheda tecnica(HTML) 17 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38

Scheda tecnica Scarica

Link URL