DAC7553_14 datasheet(15/26 Pages) TI1

15 / 26 page

www.ti.com

THEORY OF OPERATION

D/A SECTION

OUTPUT BUFFER AMPLIFIERS

DAC External Reference Input

Resistor String

Ref +

Ref −

DAC Register

VOUT

VREF

GND

VFB

100 kW

50 kW

Amplifier Sense Input

VREF

To Output

Amplifier

GND

RESISTOR STRING

Power-On Reset

DAC7553

SLAS477 – SEPTEMBER 2005

The architecture of the DAC7553 consists of a string

The output buffer amplifier is capable of generating

DAC followed by an output buffer amplifier. Figure 29

rail-to-rail voltages on its output, which gives an

shows a generalized block diagram of the DAC

output range of 0 V to VDD. It is capable of driving a

architecture.

load of 2 k

Ω in parallel with up to 1000 pF to GND.

The source and sink capabilities of the output

amplifier can be seen in the typical curves. The slew

rate is 1.8 V/µs with a typical settling time of 3 µs with

the output unloaded.

Two separate reference pins are provided for two

DACs, providing maximum flexibility. VREFA serves

DAC A and VREFB serves DAC B. VREFA and

Figure 29. Typical DAC Architecture

VREFB can be externally shorted together for

simplicity.

The 2s-complement input coding to the DAC7553

It is recommended to use a buffered reference in the

gives the ideal output voltage as:

external circuit (e.g., REF3140). The input impedance

VOUT = VREF × D/4096

is typically 100 k

Ω for each reference input pin..

Where D = decimal equivalent of the 2s-complement

input that is loaded to the DAC register, which can

range from 0 to 4095.

The DAC7553 contains two amplifier feedback input

pins, VFBA and VFBB. For voltage output operation,

VFBA and VFBB must externally connect to VOUTA

and VOUTB, respectively. For better DC accuracy,

these connections should be made at load points.

The VFBA and VFBB pins are also useful for a

variety of applications, including digitally controlled

current sources. Each feedback input pin is internally

connected to the DAC amplifier's negative input

terminal

through

100-k

Ω resistor; and, the

Figure 30. Typical Resistor String

amplifier's negative input terminal internally connects

to ground through another 100-k

Ω resistor (See

Figure 29). This forms a gain-of-two, noninverting

amplifier configuration. Overall gain remains one

The resistor string section is shown in Figure 30. It is

because the resistor string has a divide-by-two

simply a string of resistors, each of value R. The

configuration. The resistance seen at each VFBx pin

digital code loaded to the DAC register determines at

is approximately 200 k

Ω to ground.

which node on the string the voltage is tapped off to

be fed into the output amplifier. The voltage is tapped

off by closing one of the switches connecting the

On power up, all internal registers are cleared and all

string to the amplifier. Because it is a string of

channels are updated with midscale voltages. Until

resistors, it is specified monotonic. The DAC7553

valid data is written, all DAC outputs remain in this

architecture uses four separate resistor strings to

state. This is particularly useful in applications where

minimize channel-to-channel crosstalk.

it is important to know the state of the DAC outputs

while the device is powering up. In order not to turn

on ESD protection devices, VDD should be applied

before any other pin is brought high.

DAC7553 Scheda tecnica(PDF) 15 Page - Texas Instruments

DAC7553 Scheda tecnica(HTML) 15 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

Scheda tecnica Scarica

Link URL