AD9957SLASHPCBZ datasheet(59/61 Pages) AD

59 / 61 page

Data Sheet

AD9957

Rev. F | Page 59 of 61

RAM Segment Register 1

Address 0x06, six bytes are assigned to this register. This register is only active if CFR1, Bit 31 = 1 and there is a Logic 1 to Logic 0

transition on the RT pin.

Table 24. Bit Descriptions for RAM Segment Register 1

Bit(s)

Mnemonic

Description

[47:32]

RAM Address Step

Rate 1

This 16-bit number controls the rate at which the RAM state machine steps through the specified RAM

address range.

[31:22]

RAM End Address 1

This 10-bit number identifies the ending address for the RAM state machine.

[21:16]

Open

[15:6]

RAM Start Address 1

This 10-bit number identifies the starting address for the RAM state machine.

[5:3]

Open

[2:0]

RAM Playback Mode 1

This 3-bit number identifies the playback mode for the RAM state machine (see Table 5).

Amplitude Scale Factor (ASF) Register

Address 0x09, four bytes are assigned to this register. This register is only active if CFR1, Bit 9 = 1.

Table 25. Bit Descriptions for ASF Register

Bit(s)

Mnemonic

Description

[31:16]

Amplitude Ramp Rate

Ineffective unless CFR1, Bit 8 = 1. This 16-bit number controls the rate at which the OSK controller

updates amplitude changes to the DDS.

[15:2]

Amplitude Scale Factor

If CFR1, Bit 8 = 0 and CFR1, Bit 23 = 0, then this 14-bit number is the amplitude scale factor for the DDS.

If CFR1, Bit 8 = 0 and CFR1, Bit 23 = 1, then this 14-bit number is the amplitude scale factor for the DDS

when the OSK pin is Logic 1.

If CFR1, Bit 8 = 1, then this 14-bit number sets a ceiling on the maximum allowable amplitude scale

factor for the DDS.

[1:0]

Amplitude Step Size

Ineffective unless CFR1, Bit 8 = 1. This 2-bit number controls the step size for amplitude changes to the

DDS (see Table 9).

Multichip Sync Register

Address 0x0A, four bytes are assigned to this register.

Table 26. Bit Descriptions for the Multichip Sync Register

Bit(s)

Mnemonic

Description

[31:28]

Sync Validation Delay

Default is 0000b. This 4-bit number sets the timing skew (in ~75 ps increments) between SYSCLK and

the delayed sync-in signal for the synchronization validation block in the synchronization receiver.

Sync Receiver Enable

0: synchronization clock receiver disabled (default).

1: synchronization clock receiver enabled.

Sync Generator Enable

0: synchronization clock generator disabled (default).

1: synchronization clock generator enabled.

Sync Generator Polarity

0: synchronization clock generator coincident with the rising edge of the system clock (default).

1: synchronization clock generator coincident with the falling edge of the system clock.

Open

[23:18]

Sync State Preset Value

Default is 000000b. This 6-bit number is the state that the internal clock generator assumes when it

receives a sync pulse.

[17:16]

Open

[15:11]

Sync Generator Delay

Default is 00000b. This 5-bit number sets the output delay (in ~75 ps increments) of the

synchronization generator.

[10:8]

Open

[7:3]

Sync Receiver Delay

Default is 00000b. This 5-bit number sets the delay input delay (in ~75 ps increments) of the

synchronization receiver.

[2:0]

Open

AD9957/PCBZ Scheda tecnica(PDF) 59 Page - Analog Devices

AD9957/PCBZ Scheda tecnica(HTML) 59 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61

Scheda tecnica Scarica

Link URL