| Motore di ricerca datesheet componenti elettronici |
|
ST25DV16KC-JF8D3 Scheda tecnica(PDF) 45 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
ST25DV16KC-JF8D3 Scheda tecnica(HTML) 45 Page - STMicroelectronics |
|
45 / 203 page ![]() Table 33. GPO2 Bit Name Function Factory value b7-b5 RFU - 000b b4-b2 IT_TIME Pulse duration = 301 us - IT_TIME x 37.65 us ± 2 us 011b b1 I2C_RF_OFF_EN 0: disabled 1: A pulse is emitted on GPO when I2C host has successfully switched the RF off. 0b b0 I2C_WRITE_EN 0: disabled 1: A pulse is emitted on GPO at completion of valid I2C write operation in EEPROM 0b Note: Refer to Table 13. System configuration memory map for the GPO2 register. • Defines interrupt pulse duration on GPO pin for the flowing events: RF_INTERRUPT, FIELD_CHANGE, RF_PUT_MSG, RF_GET_MSG, RF_WRITE , I2C_RF_OFF_EN and I2C_WRITE_EN. • See Eq. (1) for interrupt duration calculation. Table 34. GPO_CTRL_Dyn access RF I2C Command Type Address Type Read Dynamic Configuration (cmd code ADh) @00h Fast Read Dynamic Configuration (cmd code CDh) @00h RO E2=0, E1=1, 2000h b7-b1: RO b0 : R always, W always Table 35. GPO_CTRL_Dyn Bit Name Function Factory value b7-b1 RFU - 0000000b b0 GPO_EN 0: GPO output is disabled. GPO is High-Z (open drain version) or is tied to ground (CMOS version). 1: GPO output is enabled. GPO outputs enabled interrupts. 1b Note: Refer to Table 14. Dynamic registers memory map for the GPO_CTRL_Dyn register. • Allows I2C host to dynamically enable or disable GPO output by writing in GPO_EN bit (b0). • GPO_EN bit of GPO_CTRL_Dyn register is prevalent over GPO_EN bit of GPO register. • At power up, and each time GPO register is updated, GPO_EN bit content is copied from GPO register. • GPO_CTRL_Dyn is a volatile register. Value is maintained only if at least one of the two power sources is present (RF field or VCC). • GPO_CTRL_Dyn bit 0 (GPO_EN) can be written even if I2C security session is closed (I2C password not presented) but is read only for RF user. • Modifying GPO_CTRL_Dyn bit 0 (GPO_EN), does not affect the value of GPO register bit 0 GPO_EN Table 36. IT_STS_Dyn access RF I2C Command Type Address Type No access E2=0, E1=1, 2005h RO ST25DV04KC ST25DV16KC ST25DV64KC GPO DS13519 - Rev 3 page 45/203 |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |