R8C datasheet(109/199 Pages) RENESAS

109 / 199 page

R8C/10 Group

13.2 Clock Asynchronous Serial I/O (UART) Mode

Rev.1.20 Jan 27, 2006

page 99 of 180

REJ09B0019-0120

Item

Specification

Transfer data format

• Character bit (transfer data): selectable from 7, 8 or 9 bits

• Start bit: 1 bit

• Parity bit: selectable from odd, even, or none

• Stop bit: selectable from 1 or 2 bits

Transfer clock

• UiMR(i=0, 1) register CKDIR bit = 0 (internal clock) : fj/(16(n+1))

fj=f1SIO, f8SIO, f32SIO n=setting value in UiBRG register: 0016 to FF16

• CKDIR bit = “1” (external clock) : fEXT/(16(n+1))

fEXT: input from CLKi pin

n=setting value in UiBRG register: 0016 to FF16

Transmission start condition

• Before transmission can start, the following requirements must be met

_ TE bit in UiC1 register= 1 (transmission enabled)

_ TI bit in UiC1 register = 0 (data present in UiTB register)

Reception start condition

• Before reception can start, the following requirements must be met

_ RE bit in UiC1 register= 1 (reception enabled)

_ Start bit detection

Interrupt request

• For transmission, one of the following conditions can be selected

generation timing

_ UiIRS bit = 0 (transmit buffer empty): when transferring data from UiTB register to

UARTi transmit register (at start of transmission)

_ UiIRS bit =1 (transfer completed): when serial interface finished sending data from

UARTi transmit register

• For reception

When transferring data from UARTi receive register to UiRB register (at completion

of reception)

Error detection

• Overrun error(1)

This error occurs if serial interface started receiving the next data before reading

UiRB register and received the bit one before the last stop bit of the next data

• Framing error

This error occurs when the number of stop bits set is not detected

• Parity error

This error occurs when if parity is enabled, the number of 1’s in parity and character

bits does not match the number of 1’s set

• Error sum flag

This flag is set (= 1) when any of the overrun, framing, and parity errors is encountered

Select function

• TXD10, RXD1 selection (UART)

P37 pin can be used as RxD1 pin or TxD10 pin in UART1. Select by a program.

• TxD11 pin selection (UART1)

P00 pin can be used as TxD11 pin in UART1 or port P00. Select by a program.

NOTES:

1. If an overrun error occurs, the value of U0RB register will be indeterminate. The IR bit in the S0RIC register does

not change.

13.2 Clock Asynchronous Serial I/O (UART) Mode

The UART mode allows transmitting and receiving data after setting the desired bit rate and transfer data

format. Tables 13.4 lists the specifications of the UART mode. Table 13.5 lists the registers and settings

for UART mode.

Table 13.4 UART Mode Specifications

R8C Scheda tecnica(PDF) 109 Page - Renesas Technology Corp

R8C Scheda tecnica(HTML) 109 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL