| Motore di ricerca datesheet componenti elettronici |
|
PIC16F716 Scheda tecnica(PDF) 70 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F716 Scheda tecnica(HTML) 70 Page - Microchip Technology |
|
70 / 136 page ![]() PIC16F716 DS41206B-page 68 © 2007 Microchip Technology Inc. 9.8 Time-out Sequence On power-up, the time-out sequence is as follows: First PWRT time-out is invoked after the POR time delay has expired. Then OST is activated. The total time-out will vary based on oscillator configuration and the status of the PWRT. For example, in RC mode with the PWRT disabled, there will be no time-out at all. Figure 9-10, Figure 9-11, and Figure 9-12 depict time-out sequences on power-up. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high will begin execution immediately (Figure 9-12). This is useful for testing purposes or to synchronize more than one PIC16F716 device operating in parallel. Table 9-5 shows the Reset conditions for some Special Function Registers, while Table 9-6 shows the Reset conditions for all the registers. 9.9 Power Control/STATUS Register (PCON) The Power Control/STATUS Register, PCON has two bits. Bit 0 is the Brown-out Reset Status bit, BOR. If the BOREN Configuration bit is set, BOR is ‘1’ on Power-on Reset and reset to ‘0’ when a Brown-out con- dition occurs. BOR must then be set by the user and checked on subsequent resets to see if it is clear, indi- cating that another Brown-out has occurred. If the BOREN Configuration bit is clear, BOR is unknown on Power-on Reset. Bit 1 is POR (Power-on Reset Status bit). It is cleared on a Power-on Reset and unaffected otherwise. The user must set this bit following a Power-on Reset. TABLE 9-3: TIME-OUT IN VARIOUS SITUATIONS TABLE 9-4: STATUS BITS AND THEIR SIGNIFICANCE Oscillator Configuration Power-up or Brown-out Wake-up from Sleep PWRTE = 0 PWRTE = 1 XT, HS, LP 72 ms + 1024 TOSC 1024 TOSC 1024 TOSC RC 72 ms — — POR BOR TO PD 0x 1 1 Power-on Reset (BOREN = 0) 01 1 1 Power-on Reset (BOREN = 1) 0x 0 x Illegal, TO is set on POR 0x x 0 Illegal, PD is set on POR 10 1 1 Brown-out Reset 11 0 1 WDT Reset 11 0 0 WDT Wake-up 11 u u MCLR Reset during normal operation 11 1 0 MCLR Reset during Sleep or interrupt wake-up from Sleep |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |