PIC16F716 datasheet(98/136 Pages) MICROCHIP

98 / 136 page

PIC16F716

DS41206B-page 96

12.4

DC Characteristics: PIC16F716 (Industrial, Extended)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC spec Section 12.1 “DC Charac-

teristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Character-

istics: PIC16F716 (Industrial, Extended)”.

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

Input Low Voltage

VIL

I/O ports

D030

D030A

with TTL buffer

VSS

—

0.8

0.15 VDD

4.5V

≤ VDD ≤ 5.5V

otherwise

D031

with Schmitt Trigger buffer

VSS

—

0.2 VDD

D032

MCLR, OSC1 (in RC mode)

VSS

—

0.2 VDD

D033

OSC1 (in HS mode)

OSC1 (in XT and LP modes)

VSS

—

0.3 VDD

0.6

(Note1)

Input High Voltage

VIH

I/O ports

—

D040

with TTL buffer

2.0

—

VDD

V4.5V

≤ VDD ≤ 5.5V

D040A

0.25 VDD +

0.8V

—VDD

otherwise

D041

with Schmitt Trigger buffer

0.8 VDD

—VDD

For entire VDD range

D042

MCLR

0.8 VDD

—VDD

D042A

OSC1 (XT, HS and LP modes)

0.7 VDD

—VDD

(Note1)

D043

OSC1 (in RC mode)

0.9 VDD

—VDD

Input Leakage Current(2), (3)

D060

IIL

I/O ports

—

±1

±500

μA

Vss

≤ VPIN ≤ VDD, Pin at

high-impedance

Vss

≤ VPIN ≤ VDD, Pin configured as

analog input

D061

MCLR, RA4/T0CKI

—

±5

μA Vss ≤ VPIN ≤ VDD

D063

OSC1/CLKIN

—

±5

μA Vss ≤ VPIN ≤ VDD, XT, HS and LP osc

modes

D070

IPURB

PORTB weak pull-up current

250

400

μAVDD = 5V, VPIN = VSS

Output Low Voltage

D080

VOL

I/O ports

—

0.6

IOL = 8.5 mA, VDD = 4.5V, -40

°C to

+85

°C

——

0.6

IOL = 7.0 mA, VDD = 4.5V, -40

°C to

+125

°C

D083

OSC2/CLKOUT (RC Osc mode)

—

0.6

IOL = 1.6 mA, VDD = 4.5V, -40

°C to

+85

°C

——

0.6

IOL = 1.2 mA, VDD = 4.5V, -40

°C to

+125

°C

Output High Voltage

D090

VOH

I/O ports(3)

VDD-0.7

—

IOH = -3.0 mA, VDD = 4.5V, -40

°C to

+85

°C

VDD-0.7

—

IOH = -2.5 mA, VDD = 4.5V, -40

°C to

+125

°C

D092

OSC2/CLKOUT (RC Osc mode)

VDD-0.7

—

IOH = -1.3 mA, VDD = 4.5V, -40

°C to

+85

°C

VDD-0.7

—

IOH = -1.0 mA, VDD = 4.5V, -40

°C to

+125

°C

D150*

VOD

Open-Drain High Voltage

—

8.5

RA4 pin

Capacitive Loading Specs on Output Pins

D100

COSC2 OSC2/CLKOUT pin

—

In XT, HS and LP modes when external

clock is used to drive OSC1.

D101

CIO

All I/O pins and OSC2 (in RC mode)

—

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5V, 25

°C unless otherwise stated. These parameters are for design guidance only and are not tested.

Note

In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC® be driven with

external clock in RC mode.

The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent

normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

PIC16F716 Scheda tecnica(PDF) 98 Page - Microchip Technology

PIC16F716 Scheda tecnica(HTML) 98 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL