| Motore di ricerca datesheet componenti elettronici |
|
A40MX02-2PL100M Scheda tecnica(PDF) 47 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
A40MX02-2PL100M Scheda tecnica(HTML) 47 Page - Microsemi Corporation |
|
47 / 142 page ![]() 40MX and 42MX FPGA Families Re vi s i on 11 1 - 43 Table 1-29 • A40MX02 Timing Characteristics (Nominal 3.3 V Operation) (Worst-Case Commercial Conditions, VCC = 3.0 V, TJ = 70°C) –3 Speed –2 Speed –1 Speed Std Speed –F Speed Parameter / Description Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Units Logic Module Propagation Delays tPD1 Single Module 1.7 2.0 2.3 2.7 3.7 ns tPD2 Dual-Module Macros 3.7 4.3 4.9 5.7 8.0 ns tCO Sequential Clock-to-Q 1.7 2.0 2.3 2.7 3.7 ns tGO Latch G-to-Q 1.7 2.0 2.3 2.7 3.7 ns tRS Flip-Flop (Latch) Reset-to-Q 1.7 2.0 2.3 2.7 3.7 ns Logic Module Predicted Routing Delays1 tRD1 FO = 1 Routing Delay 2.0 2.2 2.5 3.0 4.2 ns tRD2 FO = 2 Routing Delay 2.7 3.1 3.5 4.1 5.7 ns tRD3 FO = 3 Routing Delay 3.4 3.9 4.4 5.2 7.3 ns tRD4 FO = 4 Routing Delay 4.2 4.8 5.4 6.3 8.9 ns tRD8 FO = 8 Routing Delay 7.1 8.2 9.2 10.9 15.2 ns Logic Module Sequential Timing2 tSUD Flip-Flop (Latch) Data Input Set-Up 4.3 4.9 5.6 6.6 9.2 ns tHD 3 Flip-Flop (Latch) Data Input Hold 0.0 0.0 0.0 0.0 0.0 ns tSUENA Flip-Flop (Latch) Enable Set-Up 4.3 4.9 5.6 6.6 9.2 ns tHENA Flip-Flop (Latch) Enable Hold 0.0 0.0 0.0 0.0 0.0 ns tWCLKA Flip-Flop (Latch) Clock Active Pulse Width 4.6 5.3 6.0 7.0 9.8 ns tWASYN Flip-Flop (Latch) Asynchronous Pulse Width 4.6 5.3 6.0 7.0 9.8 ns tA Flip-Flop Clock Input Period 6.8 7.8 8.9 10.4 14.6 ns fMAX Flip-Flop (Latch) Clock Frequency (FO = 128) 109 101 92 80 48 MHz Input Module Propagation Delays tINYH Pad-to-Y HIGH 1.0 1.1 1.3 1.5 2.1 ns tINYL Pad-to-Y LOW 0.9 1.0 1.1 1.3 1.9 ns Notes: 1. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual performance. 2. Set-up times assume fanout of 3. Further testing information can be obtained from the Timer utility. 3. The hold time for the DFME1A macro may be greater than 0 ns. Use the Timer tool from the Designer software to check the hold time for this macro. 4. Delays based on 35 pF loading. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |