| Motore di ricerca datesheet componenti elettronici |
|
A40MX02-2PL100M Scheda tecnica(PDF) 56 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
A40MX02-2PL100M Scheda tecnica(HTML) 56 Page - Microsemi Corporation |
|
56 / 142 page ![]() 40MX and 42MX FPGA Families 1- 52 R e v i sio n 1 1 Table 1-32 • A42MX09 Timing Characteristics (Nominal 5.0 V Operation) (Worst-Case Commercial Conditions, VCCA = 4.75 V, TJ = 70°C) –3 Speed –2 Speed –1 Speed Std Speed –F Speed Units Parameter / Description Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Logic Module Propagation Delays1 tPD1 Single Module 1.2 1.3 1.5 1.8 2.5 ns tCO Sequential Clock-to-Q 1.3 1.4 1.6 1.9 2.7 ns tGO Latch G-to-Q 1.2 1.4 1.6 1.8 2.6 ns tRS Flip-Flop (Latch) Reset-to-Q 1.2 1.6 1.8 2.1 2.9 ns Logic Module Predicted Routing Delays2 tRD1 FO = 1 Routing Delay 0.7 0.8 0.9 1.0 1.4 ns tRD2 FO = 2 Routing Delay 0.9 1.0 1.2 1.4 1.9 ns tRD3 FO = 3 Routing Delay 1.2 1.3 1.5 1.7 2.4 ns tRD4 FO = 4 Routing Delay 1.4 1.5 1.7 2.0 2.9 ns tRD8 FO = 8 Routing Delay 2.3 2.6 2.9 3.4 4.8 ns Logic Module Sequential Timing3, 4 tSUD Flip-Flop (Latch) Data Input Set-Up 0.3 0.4 0.4 0.5 0.7 ns tHD Flip-Flop (Latch) Data Input Hold 0.0 0.0 0.0 0.0 0.0 ns tSUENA Flip-Flop (Latch) Enable Set-Up 0.4 0.5 0.5 0.6 0.8 ns tHENA Flip-Flop (Latch) Enable Hold 0.0 0.0 0.0 0.0 0.0 ns tWCLKA Flip-Flop (Latch) Clock Active Pulse Width 3.4 3.8 4.3 5.0 7.0 ns tWASYN Flip-Flop (Latch) Asynchronous Pulse Width 4.5 4.9 5.6 6.6 9.2 ns tA Flip-Flop Clock Input Period 3.5 3.8 4.3 5.1 7.1 ns tINH Input Buffer Latch Hold 0.0 0.0 0.0 0.0 0.0 ns tINSU Input Buffer Latch Set-Up 0.3 0.3 0.4 0.4 0.6 ns tOUTH Output Buffer Latch Hold 0.0 0.0 0.0 0.0 0.0 ns tOUTSU Output Buffer Latch Set-Up 0.3 0.3 0.4 0.4 0.6 ns fMAX Flip-Flop (Latch) Clock Frequency 268 244 224 195 117 MHz Notes: 1. For dual-module macros, use tPD1 + tRD1 + tPDn, tCO + tRD1 + tPDn, or tPD1 + tRD1 + tSUD, whichever is appropriate. 2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual performance. 3. Data applies to macros based on the S-module. Timing parameters for sequential macros constructed from C-modules can be obtained from the Timer utility. 4. Set-up and hold timing parameters for the input buffer latch are defined with respect to the PAD and the D input. External setup/hold timing parameters must account for delay from an external PAD signal to the G inputs. Delay from an external PAD signal to the G input subtracts (adds) to the internal setup (hold) time. 5. Delays based on 35 pF loading. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |