| Motore di ricerca datesheet componenti elettronici |
|
A40MX02-2PL100M Scheda tecnica(PDF) 60 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
A40MX02-2PL100M Scheda tecnica(HTML) 60 Page - Microsemi Corporation |
|
60 / 142 page ![]() 40MX and 42MX FPGA Families 1- 56 R e v i sio n 1 1 Table 1-33 • A42MX09 Timing Characteristics (Nominal 3.3 V Operation) (Worst-Case Commercial Conditions, VCCA = 3.0 V, TJ = 70°C) –3 Speed –2 Speed –1 Speed Std Speed –F Speed Units Parameter / Description Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Logic Module Propagation Delays1 tPD1 Single Module 1.6 1.8 2.1 2.5 3.5 ns tCO Sequential Clock-to-Q 1.8 2.0 2.3 2.7 3.8 ns tGO Latch G-to-Q 1.7 1.9 2.1 2.5 3.5 ns tRS Flip-Flop (Latch) Reset-to-Q 2.0 2.2 2.5 2.9 4.1 ns Logic Module Predicted Routing Delays2 tRD1 FO = 1 Routing Delay 1.0 1.1 1.2 1.4 2.0 ns tRD2 FO = 2 Routing Delay 1.3 1.4 1.6 1.9 2.7 ns tRD3 FO = 3 Routing Delay 1.6 1.8 2.0 2.4 3.3 ns tRD4 FO = 4 Routing Delay 1.9 2.1 2.4 2.9 4.0 ns tRD8 FO = 8 Routing Delay 3.2 3.6 4.1 4.8 6.7 ns Logic Module Sequential Timing 3, 4 tSUD Flip-Flop (Latch) Data Input Set-Up 0.5 0.5 0.6 0.7 0.9 ns tHD Flip-Flop (Latch) Data Input Hold 0.0 0.0 0.0 0.0 0.0 ns tSUENA Flip-Flop (Latch) Enable Set-Up 0.6 0.6 0.7 0.8 1.2 ns tHENA Flip-Flop (Latch) Enable Hold 0.0 0.0 0.0 0.0 0.0 ns tWCLKA Flip-Flop (Latch) Clock Active Pulse Width 4.7 5.3 6.0 7.0 9.8 ns tWASYN Flip-Flop (Latch) Asynchronous Pulse Width 6.2 6.9 7.8 9.2 12.9 ns tA Flip-Flop Clock Input Period 5.0 5.6 6.2 7.1 9.9 ns tINH Input Buffer Latch Hold 0.0 0.0 0.0 0.0 0.0 ns tINSU Input Buffer Latch Set-Up 0.3 0.3 0.3 0.4 0.6 ns tOUTH Output Buffer Latch Hold 0.0 0.0 0.0 0.0 0.0 ns tOUTSU Output Buffer Latch Set-Up 0.3 0.3 0.3 0.4 0.6 ns fMAX Flip-Flop (Latch) Clock Frequency 161 146 135 117 70 MHz Notes: 1. For dual-module macros, use tPD1 + tRD1 + tPDn, tCO + tRD1 + tPDn, or tPD1 + tRD1 + tSUD, whichever is appropriate. 2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual performance. 3. Data applies to macros based on the S-module. Timing parameters for sequential macros constructed from C-modules can be obtained from the Timer utility. 4. Set-up and hold timing parameters for the input buffer latch are defined with respect to the PAD and the D input. External setup/hold timing parameters must account for delay from an external PAD signal to the G inputs. Delay from an external PAD signal to the G input subtracts (adds) to the internal setup (hold) time. 5. Delays based on 35 pF loading. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |