| Motore di ricerca datesheet componenti elettronici |
|
A40MX02-2PL100M Scheda tecnica(PDF) 76 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
A40MX02-2PL100M Scheda tecnica(HTML) 76 Page - Microsemi Corporation |
|
76 / 142 page ![]() 40MX and 42MX FPGA Families 1- 72 R e v i sio n 1 1 Input Module Predicted Routing Delays2 tIRD1 FO = 1 Routing Delay 2.6 2.9 3.2 3.8 5.3 ns tIRD2 FO = 2 Routing Delay 2.9 3.2 3.6 4.3 6.0 ns tIRD3 FO = 3 Routing Delay 3.2 3.6 4.0 4.8 6.6 ns tIRD4 FO = 4 Routing Delay 3.5 3.9 4.4 5.2 7.3 ns tIRD8 FO = 8 Routing Delay 4.8 5.3 6.1 7.1 10.0 ns Global Clock Network tCKH Input LOW to HIGH FO = 32 FO = 486 4.4 4.8 4.8 5.3 5.5 6.0 6.5 7.1 9.1 10.0 ns ns tCKL Input HIGH to LOW FO = 32 FO = 486 5.1 6.0 5.7 6.6 6.4 7.5 7.6 8.8 10.6 12.4 ns ns tPWH Minimum Pulse Width HIGH FO = 32 FO = 486 3.0 3.3 3.3 3.7 3.8 4.2 4.5 4.9 6.3 6.9 ns ns tPWL Minimum Pulse Width LOW FO = 32 FO = 486 3.0 3.3 3.4 3.7 3.8 4.2 4.5 4.9 6.3 6.9 ns ns tCKSW Maximum Skew FO = 32 FO = 486 0.8 0.8 0.8 0.8 1.0 1.0 1.1 1.1 1.6 1.6 ns ns tSUEXT Input Latch External Set-Up FO = 32 FO = 486 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 ns ns TTL Output Module Timing5 tDLH Data-to-Pad HIGH 3.4 3.8 4.3 5.0 7.1 ns tDHL Data-to-Pad LOW 4.0 4.4 5.0 5.9 8.3 ns tENZH Enable Pad Z to HIGH 3.6 4.0 4.5 5.3 7.4 ns tENZL Enable Pad Z to LOW 3.9 4.4 5.0 5.8 8.2 ns tENHZ Enable Pad HIGH to Z 7.2 8.0 9.1 10.7 14.9 ns tENLZ Enable Pad LOW to Z 6.7 7.5 8.5 9.9 13.9 ns tGLH G-to-Pad HIGH 4.8 5.3 6.0 7.2 10.0 ns tGHL G-to-Pad LOW 4.8 5.3 6.0 7.2 10.0 ns tLSU I/O Latch Output Set-Up 0.7 0.7 0.8 1.0 1.4 ns Table 1-37 • A42MX24 Timing Characteristics (Nominal 3.3 V Operation) (continued) (Worst-Case Commercial Conditions, VCCA = 3.0 V, TJ = 70°C) –3 Speed –2 Speed –1 Speed Std Speed –F Speed Units Parameter / Description Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Notes: 1. For dual-module macros, use tPD1 + tRD1 + tPDn, tCO + tRD1 + tPDn, or tPD1 + tRD1 + tSUD, whichever is appropriate. 2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual performance. 3. Data applies to macros based on the S-module. Timing parameters for sequential macros constructed from C-modules can be obtained from the Timer utility. 4. Set-up and hold timing parameters for the Input Buffer Latch are defined with respect to the PAD and the D input. External setup/hold timing parameters must account for delay from an external PAD signal to the G inputs. Delay from an external PAD signal to the G input subtracts (adds) to the internal setup (hold) time. 5. Delays based on 35 pF loading. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |