| Motore di ricerca datesheet componenti elettronici |
|
A40MX02-2PL100M Scheda tecnica(PDF) 65 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
A40MX02-2PL100M Scheda tecnica(HTML) 65 Page - Microsemi Corporation |
|
65 / 142 page ![]() 40MX and 42MX FPGA Families Re vi s i on 11 1 - 61 Input Module Propagation Delays tINYH Pad-to-Y HIGH 1.1 1.2 1.3 1.6 2.2 ns tINYL Pad-to-Y LOW 0.8 0.9 1.0 1.2 1.7 ns tINGH G to Y HIGH 1.4 1.6 1.8 2.1 2.9 ns tINGL G to Y LOW 1.4 1.6 1.8 2.1 2.9 ns Input Module Predicted Routing Delays2 tIRD1 FO = 1 Routing Delay 1.8 2.0 2.3 2.7 4.0 ns tIRD2 FO = 2 Routing Delay 2.1 2.3 2.6 3.1 4.3 ns tIRD3 FO = 3 Routing Delay 2.3 2.6 3.0 3.5 4.9 ns tIRD4 FO = 4 Routing Delay 2.6 3.0 3.3 3.9 5.4 ns tIRD8 FO = 8 Routing Delay 3.6 4.0 4.6 5.4 7.5 ns Global Clock Network tCKH Input LOW to HIGH FO = 32 FO = 384 2.6 2.9 2.9 3.2 3.3 3.6 3.9 4.3 5.4 6.0 ns ns tCKL Input HIGH to LOW FO = 32 FO = 384 3.8 4.5 4.2 5.0 4.8 5.6 5.6 6.6 7.8 9.2 ns ns tPWH Minimum Pulse Width HIGH FO = 32 FO = 384 3.2 3.7 3.5 4.1 4.0 4.6 4.7 5.4 6.6 7.6 ns ns tPWL Minimum Pulse Width LOW FO = 32 FO = 384 3.2 3.7 3.5 4.1 4.0 4.6 4.7 5.4 6.6 7.6 ns ns tCKSW Maximum Skew FO = 32 FO = 384 0.3 0.3 0.4 0.4 0.4 0.4 0.5 0.5 0.7 0.7 ns ns tSUEXT Input Latch External Set-Up FO = 32 FO = 384 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 ns ns tHEXT Input Latch External Hold FO = 32 FO = 384 2.8 3.2 3.1 3.5 5.5 4.0 4.1 4.7 5.7 6.6 ns ns tP Minimum Period FO = 32 FO = 384 4.2 4.6 4.67 5.1 5.1 5.6 5.8 6.4 9.7 10.7 ns ns fMAX Maximum Frequency FO = 32 FO = 384 237 215 215 195 198 179 172 156 103 94 MHz MHz Table 1-34 • A42MX16 Timing Characteristics (Nominal 5.0 V Operation) (continued) (Worst-Case Commercial Conditions, VCCA = 4.75 V, TJ = 70°C) –3 Speed –2 Speed –1 Speed Std Speed –F Speed Units Parameter / Description Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Notes: 1. For dual-module macros, use tPD1 + tRD1 + tPDn, tCO + tRD1 + tPDn, or tPD1 + tRD1 + tSUD, point and position whichever is appropriate. 2. Routing delays are for typical designs across worst-case operating conditions. These parameters should be used for estimating device performance. Post-route timing analysis or simulation is required to determine actual performance. 3. Data applies to macros based on the S-module. Timing parameters for sequential macros constructed from C-modules can be obtained from the Timer utility. 4. Set-up and hold timing parameters for the input buffer latch are defined with respect to the PAD and the D input. External setup/hold timing parameters must account for delay from an external PAD signal to the G inputs. Delay from an external PAD signal to the G input subtracts (adds) to the internal setup (hold) time. 5. Delays based on 35 pF loading. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |