JS28F256P30T85 datasheet(69/102 Pages) INTEL

69 / 102 page

1-Gbit P30 Family

Datasheet

Intel StrataFlash® Embedded Memory (P30)

April 2005

Order Number: 306666, Revision: 001

13.0

Security Modes

The device features security modes used to protect the information stored in the flash memory

array. The following sections describe each security mode in detail.

13.1

Block Locking

Individual instant block locking is used to protect user code and/or data within the flash memory

array. All blocks power up in a locked state to protect array data from being altered during power

transitions. Any block can be locked or unlocked with no latency. Locked blocks cannot be

programmed or erased; they can only be read.

Software-controlled security is implemented using the Block Lock and Block Unlock commands.

Hardware-controlled security can be implemented using the Block Lock-Down command along

with asserting WP#. Also, VPP data security can be used to inhibit program and erase operations

(see Section 11.6, “Program Protection” on page 66 and Section 12.4, “Erase Protection” on

page 68).

The P30 device also offers four pre-defined areas in the main array that can be configured as One-

Time Programmable (OTP) for the highest level of security. These include the four 32 KB

parameter blocks together as one and the three adjacent 128 KB main blocks. This is available for

top or bottom parameter devices.

13.1.1

Lock Block

To lock a block, issue the Lock Block Setup command. The next command must be the Lock Block

command issued to the desired block’s address (see Section 9.2, “Device Commands” on page 50

and Figure 46, “Block Lock Operations Flowchart” on page 91). If the Set Read Configuration

instead.

Block lock and unlock operations are not affected by the voltage level on VPP. The block lock bits

may be modified and/or read even if VPP is at or below VPPLK.

13.1.2

Unlock Block

The Unlock Block command is used to unlock blocks (see Section 9.2, “Device Commands” on

page 50). Unlocked blocks can be read, programmed, and erased. Unlocked blocks return to a

locked state when the device is reset or powered down. If a block is in a lock-down state, WP#

must be deasserted before it can be unlocked (see Figure 32, “Block Locking State Diagram” on

page 70).

13.1.3

Lock-Down Block

A locked or unlocked block can be locked-down by writing the Lock-Down Block command

sequence (see Section 9.2, “Device Commands” on page 50). Blocks in a lock-down state cannot

be programmed or erased; they can only be read. However, unlike locked blocks, their locked state

cannot be changed by software commands alone. A locked-down block can only be unlocked by

issuing the Unlock Block command with WP# deasserted. To return an unlocked block to locked-

JS28F256P30T85 Scheda tecnica(PDF) 69 Page - Intel Corporation

JS28F256P30T85 Scheda tecnica(HTML) 69 Page - Intel Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL