ATtiny13A datasheet(21/174 Pages) ATMEL

21 / 174 page

8126D–AVR–11/09

ATtiny13A

5.5.3

EECR – EEPROM Control Register

• Bit 7 – Res: Reserved Bit

This bit is reserved for future use and will always read as 0 in ATtiny13A. For compatibility with

future AVR devices, always write this bit to zero. After reading, mask out this bit.

• Bit 6 – Res: Reserved Bit

This bit is reserved in the ATtiny13A and will always read as zero.

• Bits 5:4 – EEPM[1:0]: EEPROM Programming Mode Bits

The EEPROM Programming mode bits setting defines which programming action that will be

triggered when writing EEPE. It is possible to program data in one atomic operation (erase the

old value and program the new value) or to split the Erase and Write operations in two different

operations. The Programming times for the different modes are shown in Table 5-1 on page 21.

While EEPE is set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be

reset to 0b00 unless the EEPROM is busy programming.

• Bit 3 – EERIE: EEPROM Ready Interrupt Enable

Writing EERIE to one enables the EEPROM Ready Interrupt if the I-bit in SREG is set. Writing

EERIE to zero disables the interrupt. The EEPROM Ready Interrupt generates a constant inter-

rupt when Non-volatile memory is ready for programming.

• Bit 2 – EEMPE: EEPROM Master Program Enable

The EEMPE bit determines whether writing EEPE to one will have effect or not.

When EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at the

selected address. If EEMPE is zero, setting EEPE will have no effect. When EEMPE has been

written to one by software, hardware clears the bit to zero after four clock cycles.

• Bit 1 – EEPE: EEPROM Program Enable

The EEPROM Program Enable Signal EEPE is the programming enable signal to the EEPROM.

When EEPE is written, the EEPROM will be programmed according to the EEPMn bits setting.

The EEMPE bit must be written to one before a logical one is written to EEPE, otherwise no

EEPROM write takes place. When the write access time has elapsed, the EEPE bit is cleared by

hardware. When EEPE has been set, the CPU is halted for two cycles before the next instruction

is executed.

Bit

321

0x1C

–

EEPM1

EEPM0

EERIE

EEMPE

EEPE

EERE

EECR

Read/Write

R/W

Initial Value

Table 5-1.

EEPROM Mode Bits

EEPM1

EEPM0

Programming

Time

Operation

3.4 ms

Erase and Write in one operation (Atomic Operation)

1.8 ms

Erase Only

1.8 ms

Write Only

–

Reserved for future use

ATtiny13A Scheda tecnica(PDF) 21 Page - ATMEL Corporation

ATtiny13A Scheda tecnica(HTML) 21 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL