AM1808AZCED3 datasheet(49/264 Pages) TI

49 / 264 page

AM1808

www.ti.com

SPRS653A – FEBRUARY 2010 – REVISED APRIL 2010

3.7.23

Universal Parallel Port (uPP)

Table 3-25. Universal Parallel Port (uPP) Terminal Functions

SIGNAL

POWER

TYPE(1)

PULL(2)

DESCRIPTION

GROUP(3)

NAME

NO.

VP_CLKIN0 / UHPI_HCS1 /PRU1_R30[10] / GP6[7] /

uPP 2x transmit clock

W14

CP[25]

UPP_2xTXCLK

input

PRU0_R30[25] /MMCSD1_DAT[0] / UPP_CHB_CLOCK /

I/O

CP[30]

uPP channel B clock

GP8[15]/PRU1_R31[27]

PRU0_R30[24]/ MMCSD1_CLK / UPP_CHB_START / GP8[14] /

I/O

CP[30]

uPP channel B start

PRU1_R31[26]

PRU0_R30[23] / MMCSD1_CMD / UPP_CHB_ENABLE /

I/O

CP[30]

uPP channel B enable

GP8[13]/PRU1_R31[25]

PRU0_R30[22] / PRU1_R30[8] / UPP_CHB_WAIT / GP8[12]/

I/O

CP[30]

uPP channel B wait

PRU1_R31[24]

PRU0_R30[29] /UHPI_CNTL0 / UPP_CHA_CLOCK / GP6[11]

U17

I/O

CP[24]

uPP channel A clock

PRU0_R30[28] / UHPI_HCNTL1 / UPP_CHA_START / GP6[10]

W15

I/O

CP[24]

uPP channel A start

PRU0_R30[27] / UHPI_HHWIL / UPP_CHA_ENABLE / GP6[9]

U16

I/O

CP[24]

uPP channel A enable

PRU0_R30[26] /UHPI_HRW / UPP_CHA_WAIT / GP6[8] /

T15

I/O

CP[24]

uPP channel A wait

PRU1_R31[17]

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using

the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the

device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a

pull-up, an external pull-up can be used.

(3)

This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can

be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of

power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power

supply DVDD3318_C.

Device Overview

Submit Documentation Feedback

Product Folder Link(s): AM1808

AM1808AZCED3 Scheda tecnica(PDF) 49 Page - Texas Instruments

AM1808AZCED3 Scheda tecnica(HTML) 49 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL