ATtiny261-ESSZ datasheet(188/227 Pages) ATMEL

188 / 227 page

188

7753C–AVR–07/09

ATtiny261/ATtiny461/ATtiny861

Notes:

1. All DC Characteristics contained in this data sheet are based on simulation and characterization of ATtiny261/461/861 AVR

microcontrollers manufactured in a typical process technology. These values are preliminary values representing design tar-

gets, and will be updated after characterization of actual Automotive silicon.

2. “Max” means the highest value where the pin is guaranteed to be read as low.

3. “Min” means the lowest value where the pin is guaranteed to be read as high.

4. Although each I/O port can sink more than the test conditions (10 mA at V

CC = 5V, 5 mA at VCC = 3V) under steady state

conditions (non-transient), the following must be observed:

1] The sum of all IOL, for all ports, should not exceed 60 mA.

If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater

than the listed test condition.

5. Although each I/O port can source more than the test conditions (10 mA at VCC = 5V, 5 mA at VCC = 3V) under steady state

conditions (non-transient), the following must be observed:

1] The sum of all IOH, for all ports, should not exceed 60 mA.

If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current

greater than the listed test condition.

6. Values using methods described in “Minimizing Power Consumption” on page 36. Power Reduction is enabled (PRR =

0xFF) and there is no I/O drive.

7. BOD Disabled.

ICC

Power Supply Current

Active 4MHz, VCC = 3V

(6) ATD On

1.45

Active 8MHz, VCC = 5V

(6) ATD On

3.96

Active 16MHz, VCC = 5V

(6) ATD On

7.16

Idle 4MHz, VCC = 3V

(6)

0.25

0.4

Idle 8MHz, VCC = 5V

(6)

0.96

1.2

Idle 16MHz, VCC = 5V

(6)

1.91

2.5

Power-down mode

WDT enabled, VCC = 3V

(7)

450

µA

WDT disabled, VCC = 3V

(7)

0.12

µA

WDT enabled, VCC = 5V

(7)

675

µA

WDT disabled, VCC = 5V

(7)

0.13

µA

VACIO

Analog Comparator

Input Offset Voltage

CC = 5V, Vin = VCC/2

IACLK

Analog Comparator

Input Leakage Current

CC = 5V, Vin = VCC/2

-50

A = -40°C to 125°C, VCC = 2.7V to 5.5V (unless otherwise noted)

(1) (Continued)

Symbol

Parameter

Condition

Min.

Typ.

Max.

Units

ATtiny261-ESSZ Scheda tecnica(PDF) 188 Page - ATMEL Corporation

ATtiny261-ESSZ Scheda tecnica(HTML) 188 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL