ATtiny261-ESSZ datasheet(32/227 Pages) ATMEL

32 / 227 page

7753C–AVR–07/09

ATtiny261/ATtiny461/ATtiny861

7.10

Clock Output Buffer

The device can output the system clock on the CLKO pin. To enable the output, the CKOUT

Fuse has to be programmed. This mode is suitable when the chip clock is used to drive other cir-

cuits on the system. Note that the clock will not be output during reset and the normal operation

of I/O pin will be overridden when the fuse is programmed. Any clock source, including the inter-

nal RC Oscillator, can be selected when the clock is output on CLKO. If the System Clock

Prescaler is used, it is the divided system clock that is output.

7.11

System Clock Prescaler

The ATtiny261/461/861 system clock can be divided by setting the Clock Prescale Register –

CLKPR. This feature can be used to decrease power consumption when the requirement for

processing power is low. This can be used with all clock source options, and it will affect the

clock frequency of the CPU and all synchronous peripherals. clk

I/O, clkADC, clkCPU, and clkFLASH

are divided by a factor as shown in Table 7-12.

7.11.1

Switching Time

When switching between prescaler settings, the System Clock Prescaler ensures that no

glitches occur in the clock system and that no intermediate frequency is higher than neither the

clock frequency corresponding to the previous setting, nor the clock frequency corresponding to

the new setting.

The ripple counter that implements the prescaler runs at the frequency of the undivided clock,

which may be faster than the CPU’s clock frequency. Hence, it is not possible to determine the

state of the prescaler – even if it were readable, and the exact time it takes to switch from one

clock division to another cannot be exactly predicted.

From the time the CLKPS values are written, it takes between T1 + T2 and T1 + 2*T2 before the

new clock frequency is active. In this interval, 2 active clock edges are produced. Here, T1 is the

previous clock period, and T2 is the period corresponding to the new prescaler setting.

7.12

7.12.1

OSCCAL – Oscillator Calibration Register

• Bits 7:0 – CAL7:0: Oscillator Calibration Value

The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to

remove process variations from the oscillator frequency. A pre-programmed calibration value is

automatically written to this register during chip reset, giving the Factory calibrated frequency as

specified in Table 23-1 on page 189.

The application software can write this register to change the oscillator frequency. The oscillator

can be calibrated to frequencies as specified in Table 23-1 on page 189. Calibration outside that

range is not guaranteed.

Note that this oscillator is used to time EEPROM and Flash write accesses, and these write

times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more

than 8.8 MHz. Otherwise, the EEPROM or Flash write may fail.

Bit

5432

0x31 (0x51)

CAL7

CAL6

CAL5

CAL4

CAL3

CAL2

CAL1

CAL0

OSCCAL

Read/Write

R/W

Initial Value

Device Specific Calibration Value

ATtiny261-ESSZ Scheda tecnica(PDF) 32 Page - ATMEL Corporation

ATtiny261-ESSZ Scheda tecnica(HTML) 32 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL