CDPCLK4 datasheet(207/274 Pages) ALTERA

207 / 274 page

Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family

9–49

Configuration Features

August 2012

Altera Corporation

Cyclone III Device Handbook

Volume 1

f For more information about how to connect a JTAG chain with multiple voltages

across the devices in the chain, refer to the IEEE 1149.1 (JTAG) Boundary-Scan Testing

for Cyclone III Devices chapter.

You can download data to the device on the PCB through the USB-Blaster,

MasterBlaster, ByteBlaster II, ByteBlasterMV download cable, and Ethernet-Blaster

communications cable during JTAG configuration. Configuring devices using a cable

is similar to programming devices in-system. Figure 9–24 and Figure 9–25 show the

JTAG configuration of a single Cyclone III device family.

For device VCCIO of 2.5, 3.0, and 3.3 V, refer to Figure 9–24. All I/O inputs must

maintain a maximum AC voltage of 4.1 V. Because JTAG pins do not have the internal

PCI clamping diodes to prevent voltage overshoot when using VCCIO of 2.5, 3.0, and

3.3 V, you must power up the VCC of the download cable with a 2.5-V supply from

VCCA, and you must pull TCK to ground.

Table 9–15. Dedicated JTAG Pins

Name

Pin Type

Description

TDI

Test data input

Serial input pin for instructions as well as test and programming data. Data shifts in on the

rising edge of TCK. The TDI pin is powered by the VCCIO supply. If the JTAG interface is not

required on the board, the JTAG circuitry is disabled by connecting this pin to VCC.

TDO

Test data output

Serial data output pin for instructions as well as test and programming data. Data shifts out on

the falling edge of TCK. The pin is tri-stated if data is not being shifted out of the device. The

TDO

pin is powered by VCCIO in I/O bank 1. If the JTAG interface is not required on the board, the

JTAG circuitry is disabled by leaving this pin unconnected.

TMS

Test mode select

Input pin that provides the control signal to determine the transitions of the TAP controller state

machine. Transitions in the state machine occur on the rising edge of TCK. Therefore, TMS must

be set up before the rising edge of TCK. TMS is evaluated on the rising edge of TCK. The TMS pin

is powered by the VCCIO supply. If the JTAG interface is not required on the board, the JTAG

circuitry is disabled by connecting this pin to VCC.

TCK

Test clock input

Clock input to the BST circuitry. Some operations occur at the rising edge while others occur at

the falling edge. The TCK pin is powered by the VCCIO supply. If the JTAG interface is not

required on the board, the JTAG circuitry is disabled by connecting this pin to GND.

CDPCLK4 Scheda tecnica(PDF) 207 Page - Altera Corporation

CDPCLK4 Scheda tecnica(HTML) 207 Page - Altera Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL