Motore di ricerca datesheet componenti elettronici
  Italian  ▼
ALLDATASHEETIT.COM

X  

H8S/2214 Scheda tecnica(PDF) 319 Page - Renesas Technology Corp

Il numero della parte H8S/2214
Spiegazioni elettronici  16-Bit Single-Chip Microcomputer H8S Family/H8S/2200 Series
PDF  936 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Produttore elettronici  RENESAS [Renesas Technology Corp]
Homepage  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

H8S/2214 Scheda tecnica(HTML) 319 Page - Renesas Technology Corp

Back Button H8S/2214 Datasheet HTML 315Page - Renesas Technology Corp H8S/2214 Datasheet HTML 316Page - Renesas Technology Corp H8S/2214 Datasheet HTML 317Page - Renesas Technology Corp H8S/2214 Datasheet HTML 318Page - Renesas Technology Corp H8S/2214 Datasheet HTML 319Page - Renesas Technology Corp H8S/2214 Datasheet HTML 320Page - Renesas Technology Corp H8S/2214 Datasheet HTML 321Page - Renesas Technology Corp H8S/2214 Datasheet HTML 322Page - Renesas Technology Corp H8S/2214 Datasheet HTML 323Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 319 / 936 page
background image
Section 8 Data Transfer Controller (DTC)
Rev.4.00 Sep. 18, 2008 Page 259 of 872
REJ09B0189-0400
8.2.7
DTC Enable Register (DTCER)
7
DTCE7
0
R/W
6
DTCE6
0
R/W
5
DTCE5
0
R/W
4
DTCE4
0
R/W
3
DTCE3
0
R/W
0
DTCE0
0
R/W
2
DTCE2
0
R/W
1
DTCE1
0
R/W
Bit
Initial value
R/W
:
:
:
The DTC enable registers comprise seven 8-bit readable/writable registers, DTCERA to
DTCERG, with bits corresponding to the interrupt sources that can control enabling and disabling
of DTC activation. These bits enable or disable DTC service for the corresponding interrupt
sources.
The DTC enable registers are initialized to H'00 by a reset and in hardware standby mode.
Bit n—DTC Activation Enable (DTCEn)
Bit n
DTCEn
Description
0
DTC activation by this interrupt is disabled
(Initial value)
[Clearing conditions]
• When the DISEL bit is 1 and the data transfer has ended
• When the specified number of transfers have ended
1
DTC activation by this interrupt is enabled
[Holding condition]
• When the DISEL bit is 0 and the specified number of transfers have not ended
(n = 7 to 0)
A DTCE bit can be set for each interrupt source that can activate the DTC. The correspondence
between interrupt sources and DTCE bits is shown in table 8.4, together with the vector number
generated for each interrupt controller.
For DTCE bit setting, use bit manipulation instructions such as BSET and BCLR for reading and
writing. If all interrupts are masked, multiple activation sources can be set at one time by writing
data after executing a dummy read on the relevant register.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


Scheda tecnica Scarica

Go To PDF Page


Link URL



Lei ha avuto il aiuto da alldatasheet?  [ DONATE ] 

Di alldatasheet   |   Richest di pubblicita   |   contatti   |   Privacy Policy   |   Collegamento alla scheda tecnica    |   scambio Link   |   Ricerca produttore
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com