| Motore di ricerca datesheet componenti elettronici |
|
H8S/2224 Scheda tecnica(PDF) 879 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2224 Scheda tecnica(HTML) 879 Page - Renesas Technology Corp |
|
879 / 1071 page ![]() Section 24 Power-Down Modes Rev. 5.00 Aug 08, 2006 page 793 of 982 REJ09B0054-0500 than interrupts IRQ7 to IRQ0 is generated. Software standby mode cannot be cleared if the interrupt has been masked on the CPU side or has been designated as a DTC activation source. • Clearing with the RES Pin or MRES Pin When the RES pin or MRES pin is driven low, clock oscillation is started. At the same time as clock oscillation starts, clocks are supplied to the entire this LSI chip. Note that the RES pin or MRES pin must be held low until clock oscillation settles. When the RES pin or MRES pin goes high, the CPU begins reset exception handling. • Clearing with the STBY Pin When the STBY pin is driven low, a transition is made to hardware standby mode. 24.4.3 Oscillation Settling Time after Clearing Software Standby Mode Bits STS2 to STS0 in SBYCR should be set as described below. • Using a Crystal Oscillator Set bits STS2 to STS0 so that the standby time is at least tOSC2 ms (the oscillation settling time). Table 24.3 shows the standby times for different operating frequencies and settings of bits STS2 to STS0. • Using an External Clock Any value can be set. Normally, minimum time is recommended. Note: Do not set 16 states for standby time in the F-ZTAT version. 8192 states or more should be set. Table 24.3 Oscillation Settling Time Settings STS2 STS1 STS0 Standby Time 20 MHz* 1 16 MHz* 1 13 MHz 10 MHz 8 MHz* 2 6 MHz* 2 4 MHz* 2 2 MHz* 2 Unit 0 0 0 8192 states 0.41 0.51 0.6 0.8 1.0 1.4 2.0 4.1 ms 1 16384 states 0.82 1.0 1.3 1.6 2.0 2.7 4.1 8.2 1 0 32768 states 1.6 2.0 2.5 3.3 4.1 5.5 8.2 16.4 1 65536 states 3.3 4.1 5.0 6.6 8.2 10.9 16.4 32.8 1 0 0 131072 states 6.6 8.2 10.1 13.1 16.4 21.8 32.8 65.5 1 262144 states 13.1 16.4 20.2 26.2 32.8 43.7 65.5 131.1 10 Reserved 1 16 states 0.8 1.0 1.2 1.6 2.0 2.7 4.0 8.0 µs : Recommended time setting Notes: 1. Supported only by the H8S/2239 Group. 2. The H8S/2258 Group is out of operation. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |