 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
H8S/2224 Scheda tecnica(PDF) 192 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2224 Scheda tecnica(HTML) 192 Page - Renesas Technology Corp |
|
|
192 / 1071 page  Section 3 MCU Operating Modes Rev. 5.00 Aug 08, 2006 page 106 of 982 REJ09B0054-0500 3.3 Operating Mode Descriptions 3.3.1 Mode 4 The CPU can access a 16-Mbyte address space in advanced mode. The on-chip ROM is disabled. Pins P13 to P10, and ports A, B, and C function as an address bus, ports D and E function as a data bus, and part of port F carries bus control signals. Pins P13 to P11 function as input ports immediately after a reset. Pin 10 and ports A and B function as address (A20 to A8) outputs immediately after a reset. Address (A23 to A21) output can be enabled or disabled by bits AE3 to AE0 in the pin function control register (PFCR) regardless of the corresponding data direction register (DDR) values. Pins for which address output is disabled among pins P13 to P10 and in ports A and B become port outputs when the corresponding DDR bits are set to 1. Port C always has an address (A7 to A0) output function. The initial bus mode after a reset is 16 bits, with 16-bit access to all areas. However, note that if 8- bit access is designated by the bus controller for all areas, the bus mode switches to 8 bits. 3.3.2 Mode 5 The CPU can access a 16-Mbyte address space in advanced mode. The on-chip ROM is disabled. Pins P13 to P10, and ports A, B, and C function as an address bus, ports D and E function as a data bus, and part of port F carries bus control signals. Pins P13 to P11 function as input ports immediately after a reset. Pin 10 and ports A and B function as address (A20 to A8) outputs immediately after a reset. Address (A23 to A21) output can be enabled or disabled by bits AE3 to AE0 in the pin function control register (PFCR) regardless of the corresponding data direction register (DDR) values. Pins for which address output is disabled among pins P13 to P10 and in ports A and B become port outputs when the corresponding DDR bits are set to 1. Port C always has an address (A7 to A0) output function. The initial bus mode after a reset is 8 bits, with 8-bit access to all areas. However, note that if 16- bit access is designated by the bus controller for any area, the bus mode switches to 16 bits and port E becomes a data bus. |
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
