AT83SND1CXXX-ROTIL datasheet(113/212 Pages) ATMEL

113 / 212 page

113

4109J–8051–10/06

AT8xC51SND1C

in stream packets, CRC protection is not included in this case. The CRC protection algorithm for

block data is a 16-bit CCITT polynomial.

Figure 15-8. Data Token Format

15.2.6

Clock Control

The MMC bus clock signal can be used by the host to turn the cards into energy saving mode or

to control the data flow (to avoid under-run or over-run conditions) on the bus. The host is

allowed to lower the clock frequency or shut it down.

There are a few restrictions the host must follow:

•

The bus frequency can be changed at any time (under the restrictions of maximum data

transfer frequency, defined by the cards, and the identification frequency defined by the

specification document).

•

It is an obvious requirement that the clock must be running for the card to output data or

response tokens. After the last MultiMedia Card bus transaction, the host is required, to

provide 8 (eight) clock cycles for the card to complete the operation before shutting down

the clock. Following is a list of the various bus transactions:

•

A command with no response. 8 clocks after the host command End bit.

•

A command with response. 8 clocks after the card command End bit.

•

A read data transaction. 8 clocks after the End bit of the last data block.

•

A write data transaction. 8 clocks after the CRC status token.

•

The host is allowed to shut down the clock of a “busy” card. The card will complete the

programming operation regardless of the host clock. However, the host must provide a clock

edge for the card to turn off its busy signal. Without a clock edge the card (unless previously

disconnected by a deselect command-CMD7) will force the MDAT line down, forever.

15.3

Description

The MMC controller interfaces to the C51 core through the following eight special function

registers:

MMCON0, MMCON1, MMCON2, the three MMC control registers (see Table 102 to Table 110);

MMSTA, the MMC status register (see Table 105); MMINT, the MMC interrupt register (see

Table 106); MMMSK, the MMC interrupt mask register (see Table 107); MMCMD, the MMC

command register (see Table 108); MMDAT, the MMC data register (see Table 109); and

MMCLK, the MMC clock register (see Table 110).

As shown in Figure 15-9, the MMC controller is divided in four blocks: the clock generator that

handles the MCLK (formally the MMC CLK) output to the card, the command line controller that

handles the MCMD (formally the MMC CMD) line traffic to or from the card, the data line control-

ler that handles the MDAT (formally the MMC DAT) line traffic to or from the card, and the

interrupt controller that handles the MMC controller interrupt sources. These blocks are detailed

in the following sections.

Content

Sequential Data

CRC

Block Data

Content

Block Length

AT83SND1CXXX-ROTIL Scheda tecnica(PDF) 113 Page - ATMEL Corporation

AT83SND1CXXX-ROTIL Scheda tecnica(HTML) 113 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Scheda tecnica Scarica

Link URL