ADIN1300CCPZ-R7 datasheet(55/96 Pages) AD

55 / 96 page

Data Sheet

ADIN1300

analog.com

Rev. B | 55 of 96

Table 40. Bit Descriptions for TX_NEXT_PAGE

Bits

Bit Name

Description

Reset

Access

NP_NEXT_PAGE

Next page (NP) is used by the next page function to indicate that additional next page(s) follow. Otherwise, this is

the last next page to be transmitted.

0x0

R/W

RESERVED

Reserved.

0x0

NP_MSG_PAGE

Message page (MP) is used by the next page function to indicate that this is a message page. Otherwise, this is

an unformatted page.

0x1

R/W

NP_ACK_2

Acknowledge 2 (Ack2) is used by the next page function to indicate that a device has the ability to comply with the

message.

0x0

R/W

NP_TOGGLE

Toggle (T) is used by the arbitration function to ensure synchronization with the link partner during next page

exchange. This bit always takes the opposite value of the toggle bit in the previously exchanged link code word.

0x0

[10:0]

NP_CODE

Message code field is an 11-bit wide field, encoding 2048 possible messages. If the message page bit is set to

Logic 0, the bit encoding of the link code word is interpreted as an unformatted page.

0x1

R/W

Autonegotiation Link Partner Received Next Page Register

Address: 0x0008, Reset: 0x0000, Name: LP_RX_NEXT_PAGE

This address corresponds to the autonegotiation link partner received next page register specified in Clause 28.2.4.1.7 of IEEE Standard 802.3.

Table 41. Bit Descriptions for LP_RX_NEXT_PAGE

Bits

Bit Name

Description

Reset

Access

LP_NP_NEXT_PAGE

Link partner next page (NP) is used by the next page function to indicate that the link partner sends additional

next page(s). Otherwise, this is the last next page to be transmitted.

0x0

LP_NP_ACK

This bit is used by the internal handshaking in autonegotiation and must be ignored.

0x0

1: link partner has successfully received its link code word.

0: link partner has not received its link code word.

LP_NP_MSG_PAGE

Link partner message page (MP) is used by the next page function to indicate that this is a message page.

Otherwise, this is an unformatted page.

0x0

LP_NP_ACK_2

Acknowledge 2 (Ack2) is used by the next page function to indicate that the link partner has the ability to

comply with the message.

0x0

LP_NP_TOGGLE

Link partner toggle (T) is used by the arbitration function to ensure synchronization with the link partner

during the next page exchange. This bit always takes the opposite value of the toggle bit in the previously

exchanged link code word.

0x0

[10:0]

LP_NP_CODE

Link partner message code field is an 11‑bit wide field, encoding 2048 possible messages. If the message

page bit is set to Logic 0, the bit encoding of the link code word is interpreted as an unformatted page.

0x0

Master Slave Control Register

Address: 0x0009, Reset: 0x0200, Name: MSTR_SLV_CONTROL

This address corresponds to the master slave control register specified in Clause 40.5.1.1 of IEEE Standard 802.3. Note that the default reset

value of this register is dependent on the hardware configuration pins settings.

Table 42. Bit Descriptions for MSTR_SLV_CONTROL

Bits

Bit Name

Description

Reset

Access

[15:13]

TST_MODE

Transmitter test mode operations are defined by the test mode bits as specified in

Clause 40.6.1.1.2 of IEEE Standard 802.3.

0x0

R/W

111: reserved.

110: reserved.

ADIN1300CCPZ-R7 Scheda tecnica(PDF) 55 Page - Analog Devices

ADIN1300CCPZ-R7 Scheda tecnica(HTML) 55 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Scheda tecnica Scarica

Link URL