ADIN1300CCPZ-R7 datasheet(80/96 Pages) AD

80 / 96 page

Data Sheet

ADIN1300

analog.com

Rev. B | 80 of 96

Table 103. Bit Descriptions for B_1000_RTRN_EN (Continued)

Bits

Bit Name

Description

Reset

Access

Clause 40.4.6.1 of Standard 802.3 requires a PHY that is operating in 1000BASE-T mode to retrain if it detects

that its receiver status is not okay. Such a retrain prevents data from being transmitted or received for a long

period, but does not cause the LINK_STAT_LAT bit in the direct address map to latch low.

When B_1000_RTRN_EN is clear, 1000BASE-T retrain is disabled. In this case, when the receiver status

becomes not okay, it always results in the link dropping.

1: 1000BASE-T retrain is enabled.

0: 1000BASE-T retrain is disabled.

Base 10e Enable Register

Address: 0xB403, Reset: 0x0001, Name: B_10_E_EN

When set, this register enables 10BASE-Te operation. 10BASE-Te is a variant of 10BASE-T that transmits at a lower voltage level.

Table 104. Bit Descriptions for B_10_E_EN

Bits

Bit Name

Description

Reset

Access

[15:1]

RESERVED

Reserved.

0x0

B_10_E_EN

10BASE-Te. When set, this bit enables 10BASE-Te operation, this is the default operation of the device. 10BASE-Te is a

variant of 10BASE-T that transmits at a lower voltage level.

0x1

R/W

10BASE-T Transmit Test Mode Register

Address: 0xB412, Reset: 0x0000, Name: B_10_TX_TST_MODE

This register provides the ability to transmit a 10BASE-T test signal.

Table 105. Bit Descriptions for B_10_TX_TST_MODE

Bits

Bit Name

Description

Reset

Access

[15:3]

RESERVED

Reserved.

0x0

[2:0]

B_10_TX_TST_MODE

The PHY provides the ability to transmit a 10BASE-T test signal consisting of either a 5 MHz or a 10 MHz

square wave.

0x0

R/W

111: reserved.

110: reserved.

101: reserved.

100: transmit 5 MHz square wave on Dimension 1.

011: transmit 5 MHz square wave on Dimension 0.

010: transmit 10 MHz square wave on Dimension 1.

001: transmit 10 MHz square wave on Dimension 0.

000: 10BASE-T test mode disabled.

100BASE-TX Transmit Test Mode Register

Address: 0xB413, Reset: 0x0000, Name: B_100_TX_TST_MODE

This register provides the ability to transmit a 100BASE-TX test signal.

Table 106. Bit Descriptions for B_100_TX_TST_MODE

Bits

Bit Name

Description

Reset

Access

[15:3]

RESERVED

Reserved.

0x0

ADIN1300CCPZ-R7 Scheda tecnica(PDF) 80 Page - Analog Devices

ADIN1300CCPZ-R7 Scheda tecnica(HTML) 80 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Scheda tecnica Scarica

Link URL