 |
Motore di ricerca datesheet componenti elettronici |
|
|
Motore di ricerca datesheet componenti elettronici |
|
WM8281ECS/R Scheda tecnica(PDF) 1 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
WM8281ECS/R Scheda tecnica(HTML) 1 Page - Cirrus Logic |
|
|
1 / 392 page  Low Power Audio System with Ambient Noise Cancellation and Echo Cancellation http://www.cirrus.com Copyright Cirrus Logic, Inc., 2014–2016 (All Rights Reserved) Rev 4.0 MAR ‘16 WM8281 DESCRIPTION The WM8281 is a highly-integrated low-power audio system for smartphones, tablets and other portable audio devices. It combines an advanced DSP feature set with a flexible, high- performance audio hub CODEC. The WM8281 digital core combines a quad-core, 600MMAC DSP system with a variety of power-efficient fixed-function audio processing blocks. The programmable DSP cores support advanced audio features, including multi-mic wideband noise reduction, high-performance acoustic echo cancellation (AEC), stereo ambient noise cancellation (ANC), speech enhancement, advanced media enhancement, and many more. The DSP cores are supported by a fully-flexible, all-digital mixing and routing engine with sample rate converters, for wide use-case flexibility. A SLIMbus® interface supports multi-channel audio paths and host control register access. Multiple sample rates are supported concurrently via the SLIMbus interface. Three further digital audio interfaces are provided, each supporting a wide range of standard audio sample rates and serial interface formats. Automatic sample rate detection enables seamless wideband/narrowband voice call handover. Three stereo headphone drivers each provide stereo ground- referenced or mono BTL outputs. 110dB SNR, and noise levels as low as 0.8 μVRMS, offer hi-fi quality line or headphone output. The WM8281 also features a stereo pair of 2W Class-D outputs and four channels of stereo PDM output. A signal generator for controlling haptics devices is included; vibe actuators can connect directly to the Class-D speaker output, or via an external driver on the PDM output interface. All inputs, outputs and system interfaces can function concurrently. The WM8281 supports up to eight microphone inputs, (up to six analogue, or up to eight PDM digital, or combinations of each). Microphone activity detection with interrupt is available. A smart accessory interface supports most standard 3.5mm accessories. Impedance sensing and measurement is provided for external accessory and push-button detection. The WM8281 power, clocking and output driver architectures are all designed to maximise battery life in voice, music and standby modes. Low- power ‘Sleep’ is supported, with configurable wake-up events. The WM8281 is powered from a 1.8V external supply. A separate supply is required for the Class D speaker drivers (typically direct connection to 4.2V battery). Two integrated FLLs provide support for a wide range of system clock frequencies. The WM8281 is configured using the I2C, SPI ™ or SLIMbus interfaces. The fully-differential internal analogue architecture, minimal analogue signal paths and on- chip RF noise filters ensure a very high degree of noise immunity. FEATURES 600 MIPS, 600MMAC multi-core audio-signal processor Programmable wideband, multi-mic audio processing - Cirrus Logic® stereo adaptive ambient noise cancellation - Transmit-path noise reduction and echo cancellation - Wind noise, sidetone and other programmable filters - Dynamic Range Control, Fully parametric EQs - Multiband Compression, Virtual Surround Sound Multi-channel asynchronous sample rate conversion Integrated 6/8 channel 24-bit hi-fi audio hub CODEC - 6 ADCs, 100dB SNR microphone input (48kHz) - 8 DACs, 121dB SNR headphone playback (48kHz), (48kHz, eDRE software enabled) Audio inputs - Up to 6 analogue or 8 digital microphone inputs - Single-ended or differential mic/line inputs Multi-purpose headphone / earpiece / line output drivers - 3 stereo output paths - 33mW into 32Ω load at 1% THD+N - 100mW into 16 Ω BTL load at 5% THD+N - 4mW typical headphone playback power consumption - Pop suppression functions - 0.8µVRMS noise floor (A-weighted) Stereo (2 x 2W) Class D speaker output drivers - Direct drive of external haptics vibe actuators Four-channel digital speaker (PDM) interface SLIMbus audio and control interface 3 full digital audio interfaces - Standard sample rates from 4kHz up to 192kHz - Ultrasonic accessory function support - TDM support on all AIFs - Multi-channel input/output on AIF1 and AIF2 - Stereo input/output on AIF3 Flexible clocking, derived from MCLKn, BCLKn, LRCLKn or SLIMbus 2 low-power FLLs support reference clocks down to 32kHz Advanced accessory detection functions - Low-power standby mode and configurable wake-up Configurable functions on 5 GPIO pins Integrated LDO regulators and charge pumps Small W-CSP package, 0.4mm pitch APPLICATIONS Smartphones, tablets, and multimedia handsets |
Codice articolo simile - WM8281ECS/R |
|
Descrizione simile - WM8281ECS/R |
|
|
Link URL |
| Lei ha avuto il aiuto da alldatasheet? [ DONATE ] |
Di alldatasheet | Richest di pubblicita | contatti | Privacy Policy | Collegamento alla scheda tecnica | scambio Link | Ricerca produttore All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Italian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
